| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: Reject MPA FPDU length underflow before signed receive math
A malicious connected siw peer can send an iWARP FPDU whose MPA length
field (c_hdr->mpa_len, 16 bit big-endian, peer-controlled) is smaller
than the fixed DDP/RDMAP header for the announced opcode. Soft-iWARP
parses the full header in siw_get_hdr() based on iwarp_pktinfo[opcode]
.hdr_len, but never compares mpa_len against that header length.
siw_tcp_rx_data() then derives
srx->fpdu_part_rem = be16_to_cpu(mpa_len) - fpdu_part_rcvd
+ MPA_HDR_SIZE;
where fpdu_part_rcvd equals iwarp_pktinfo[opcode].hdr_len at this
point. For a tagged WRITE (hdr_len 16, MPA_HDR_SIZE 2) the smallest
on-wire mpa_len of 0 yields fpdu_part_rem = -14, and any mpa_len below
hdr_len - MPA_HDR_SIZE underflows to a negative int.
The signed value then flows into siw_proc_write()/siw_proc_rresp() as
bytes = min(srx->fpdu_part_rem, srx->skb_new);
is handed to siw_check_mem() as an int len (whose interval check
addr + len > mem->va + mem->len is satisfied for a valid base when
len is negative), and reaches siw_rx_data() -> siw_rx_kva() /
siw_rx_umem() -> skb_copy_bits() as a signed copy length. The header
copy branch in skb_copy_bits() promotes that to size_t, producing a
multi-gigabyte read.
KASAN under a KUnit harness that drives the real kernel TCP receive
path -- a loopback AF_INET socketpair, the malformed FPDU written via
kernel_sendmsg, sk_data_ready firing in softirq, tcp_read_sock
dispatching to siw_tcp_rx_data -- reports:
BUG: KASAN: use-after-free in skb_copy_bits+0x284/0x480
Read of size 4294967295 at addr ffff888...
Call Trace:
skb_copy_bits
siw_rx_kva
siw_rx_data
siw_check_mem
siw_proc_write
siw_tcp_rx_data
__tcp_read_sock
siw_qp_llp_data_ready
tcp_data_ready
tcp_data_queue
Add the missing invariant at the earliest point where the peer header
is fully assembled. iwarp_pktinfo[*].hdr_len - MPA_HDR_SIZE is exactly
the value the siw transmitter uses as the minimum mpa_len for each
opcode (drivers/infiniband/sw/siw/siw_qp.c:33), so this matches the
protocol contract. Out-of-range FPDUs terminate the connection with
TERM_ERROR_LAYER_LLP / LLP_ETYPE_MPA / LLP_ECODE_FPDU_START -- which
is RFC 5044 Section 8 error code 3 ("Marker and ULPDU Length fields
do not agree on the start of an FPDU"), the correct framing-error
class for this inconsistency. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/virtio: use uninterruptible resv lock for plane updates
virtio_gpu_cursor_plane_update() and virtio_gpu_resource_flush() lock
the framebuffer BO's dma_resv via virtio_gpu_array_lock_resv() and
ignore its return value. The function can fail with -EINTR from
dma_resv_lock_interruptible() (signal during lock wait) or with
-ENOMEM from dma_resv_reserve_fences() (fence slot allocation),
leaving the resv lock not held. The queue path then walks the object
array and calls dma_resv_add_fence(), which requires the lock held;
with lockdep enabled this trips dma_resv_assert_held():
WARNING: drivers/dma-buf/dma-resv.c:296 at dma_resv_add_fence+0x71e/0x840
Call Trace:
virtio_gpu_array_add_fence
virtio_gpu_queue_ctrl_sgs
virtio_gpu_queue_fenced_ctrl_buffer
virtio_gpu_cursor_plane_update
drm_atomic_helper_commit_planes
drm_atomic_helper_commit_tail
commit_tail
drm_atomic_helper_commit
drm_atomic_commit
drm_atomic_helper_update_plane
__setplane_atomic
drm_mode_cursor_universal
drm_mode_cursor_common
drm_mode_cursor_ioctl
drm_ioctl
__x64_sys_ioctl
Beyond the WARN, mutating the dma_resv fence list without the lock
races with concurrent readers/writers and can corrupt the list.
Both call sites run inside the .atomic_update plane callback, which
DRM atomic helpers do not allow to fail (by the time it runs, the
commit has been signed off to userspace and there is no clean
rollback path). Moving the lock acquisition to .prepare_fb was
rejected because the broader lock scope deadlocks against other BO
locking paths in the same atomic commit.
Introduce virtio_gpu_lock_one_resv_uninterruptible() that uses
dma_resv_lock() instead of dma_resv_lock_interruptible(). This
eliminates the -EINTR failure mode -- the realistic syzbot trigger
-- without extending the lock hold across the commit. The helper
locks a single BO and rejects nents > 1 with -EINVAL; both fix
sites lock exactly one BO.
Use it from virtio_gpu_cursor_plane_update() and
virtio_gpu_resource_flush(); check the return value to handle the
remaining -ENOMEM case from dma_resv_reserve_fences() by freeing
the objs and skipping the plane update for that frame. The
framebuffer BOs touched here are not shared with other contexts
and lock contention is expected to be brief, so the loss of
signal-interruptibility is acceptable.
Other callers of virtio_gpu_array_lock_resv() (the ioctl paths)
continue to use the interruptible variant.
The bug was reported by syzbot, triggered via fault injection
(fail_nth) on the DRM_IOCTL_MODE_CURSOR path, which forces the
-ENOMEM branch in dma_resv_reserve_fences(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: tls: fix off-by-one in sg_chain entry count for wrapped sk_msg ring
When an sk_msg scatterlist ring wraps (sg.end < sg.start),
tls_push_record() chains the tail portion of the ring to the head
using sg_chain(). An extra entry in the sg array is reserved for
this:
struct sk_msg_sg {
[...]
/* The extra two elements:
* 1) used for chaining the front and sections when the list becomes
* partitioned (e.g. end < start). The crypto APIs require the
* chaining;
* 2) to chain tailer SG entries after the message.
*/
struct scatterlist data[MAX_MSG_FRAGS + 2];
The current code uses MAX_SKB_FRAGS + 1 as the ring size:
sg_chain(&msg_pl->sg.data[msg_pl->sg.start],
MAX_SKB_FRAGS - msg_pl->sg.start + 1,
msg_pl->sg.data);
This places the chain pointer at
sg_chain(data[start], (MAX_SKB_FRAGS - msg_start + 1) .. =
&data[start] + (MAX_SKB_FRAGS - msg_start + 1) - 1 =
data[start + (MAX_SKB_FRAGS - start + 1) - 1] =
data[MAX_SKB_FRAGS]
instead of the true last entry. This is likely due to a "race" of
the commit under Fixes landing close to
commit 031097d9e079 ("bpf: sk_msg, zap ingress queue on psock down")
Convert to ARRAY_SIZE and drop the data[start] / - start (as suggested
by Sabrina). |
| In the Linux kernel, the following vulnerability has been resolved:
net: tls: prevent chain-after-chain in plain text SG
Sashiko points out that if end = 0 (start != 0) the current
code will create a chain link to content type right after
the wrap link:
This would create a chain where the wrap link points directly
to another chain link. The scatterlist API sg_next iterator
does not recursively resolve consecutive chain links.
meaning this is illegal input to crypto.
The wrapping link is unnecessary if end = 0. end is the entry after
the last one used so end = 0 means there's nothing pushed after
the wrap:
end start i
v v v
[ ]...[ ][ d ][ d ][ d ][ d ][rsv for wrap]
Skip the wrapping in this case.
TLS 1.3 can use the "wrapping slot" for it's chaining if end = 0.
This avoids the chain-after-chain.
Move the wrap chaining before marking END and chaining off content
type, that feels like more logical ordering to me, but should not
matter from functional perspective. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mld: fix TSO segmentation explosion when AMSDU is disabled
When the TLC notification disables AMSDU for a TID, the MLD driver sets
max_tid_amsdu_len to the sentinel value 1. The TSO segmentation path in
iwl_mld_tx_tso_segment() checks for zero but not for this sentinel,
allowing it to reach the num_subframes calculation:
num_subframes = (max_tid_amsdu_len + pad) / (subf_len + pad)
= (1 + 2) / (1534 + 2) = 0
This zero propagates to iwl_tx_tso_segment() which sets:
gso_size = num_subframes * mss = 0
Calling skb_gso_segment() with gso_size=0 creates over 32000 tiny
segments from a single GSO skb. This floods the TX ring with ~1024
micro-frames (the rest are purged), creating a massive burst of TX
completion events that can lead to memory corruption and a subsequent
use-after-free in TCP's retransmit queue (refcount underflow in
tcp_shifted_skb, NULL deref in tcp_rack_detect_loss).
The MVM driver is immune because it checks mvmsta->amsdu_enabled before
reaching the num_subframes calculation. The MLD driver has no equivalent
bitmap check and relies solely on max_tid_amsdu_len, which does not
catch the sentinel value.
Fix this by detecting the sentinel value (max_tid_amsdu_len == 1) at the
existing check and falling back to non-AMSDU TSO segmentation. Also add
a WARN_ON_ONCE guard after the num_subframes division as defense-in-depth
to catch any future code paths that produce zero through a different
mechanism. |
| In the Linux kernel, the following vulnerability has been resolved:
igc: set tx buffer type for SMD frames
Sashiko pointed out that igc_fpe_init_smd_frame() initializes
igc_tx_buffer fields for an SMD skb, but does not set the buffer type:
https://sashiko.dev/#/patchset/20260415025226.114115-1-kohei%40enjuk.jp
Since igc_tx_buffer entries are reused, a stale XDP or XSK type can
remain and make TX completion use the wrong cleanup path.
Set the buffer type to IGC_TX_BUFFER_TYPE_SKB. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix DATA decrypt vs splice() by copying data to buffer in recvmsg
This improves the fix for CVE-2026-43500.
Fix the pagecache corruption from in-place decryption of a DATA packet
transmitted locally by splice() by getting rid of the packet sharing in the
I/O thread and unconditionally extracting the packet content into a bounce
buffer in which the buffer is decrypted. recvmsg() (or the kernel
equivalent) then copies the data from the bounce buffer to the destination
buffer. The sk_buff then remains unmodified.
This has an additional advantage in that the packet is then arranged in the
buffer with the correct alignment required for the crypto algorithms to
process directly. The performance of the crypto does seem to be a little
faster and, surprisingly, the unencrypted performance doesn't seem to
change much - possibly due to removing complexity from the I/O thread.
Yet another advantage is that the I/O thread doesn't have to copy packets
which would slow down packet distribution, ACK generation, etc..
The buffer belongs to the call and is allocated initially at 2K,
sufficiently large to hold a whole jumbo subpacket, but the buffer will be
increased in size if needed. However, to take this work, MSG_PEEK may
cause a later packet to be decrypted into the buffer, in which case the
earlier one will need re-decrypting for a subsequent recvmsg().
Note that rx_pkt_offset may legitimately see 0 as a valid offset now, so
switch to using USHRT_MAX to indicate an invalid offset.
Note also that I would generally prefer to replace the buffers of the
current sk_buff with a new kmalloc'd buffer of the right size, ditching the
old data and frags as this makes the handling of MSG_PEEK easier and
removes the re-decryption issue, but this looks like quite a complicated
thing to achieve. skb_morph() looks half way to what I want, but I don't
want to have to allocate a new sk_buff. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mana: validate rx_req_idx to prevent out-of-bounds array access
In mana_hwc_rx_event_handler(), rx_req_idx is derived from
sge->address in DMA-coherent memory. In Confidential VMs
(SEV-SNP/TDX), this memory is shared unencrypted and HW can modify
WQE contents at any time. No bounds check exists on rx_req_idx,
which can lead to an out-of-bounds access into reqs[].
Add bounds check on rx_req_idx in mana_hwc_rx_event_handler() before
using it to index the reqs[] array. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: Check for underflow in xfrm_state_mtu
Leo Lin reported OOB write issue in esp component:
xfrm_state_mtu() returns u32 but performs its arithmetic in unsigned
modulo-2^32 space using an attacker-influenced "header_len + authsize +
net_adj" subtracted from a small "mtu" argument. A nobody user can
install an IPv4 ESP tunnel SA with a large authentication key
(XFRMA_ALG_AUTH_TRUNC, e.g. hmac(sha512), 64-byte key, 64-byte trunc),
configure a small interface MTU (68 bytes), and set XFRMA_TFCPAD to a
large value. When a single UDP datagram is then sent through the
tunnel, xfrm_state_mtu() underflows to a near-2^32 value, and
esp_output() consumes it as a signed int via:
padto = min(x->tfcpad, xfrm_state_mtu(x, mtu_cached))
esp.tfclen = padto - skb->len (assigned to int)
esp.tfclen ends up negative (e.g. -207). It is sign-extended to size_t
when passed to memset() inside esp_output_fill_trailer(), producing a
~16 EB write of zeroes at skb_tail_pointer(skb). KASAN logs it as
"Write of size 18446744073709551537 at addr ffff888...".
Check for underflow and return 1. This causes the sendmsg attempt to
fail with ENETUNREACH. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: Do not re-initialize smc hashtables
INIT_HLIST_HEAD(&smc_v*_hashinfo.ht) are called after smc_nl_init(),
proto_register() and sock_register(). This can lead to smc_v*_hashinfo.ht
being reset even though hash entries already exist and are being used,
possibly resulting in a corrupted list.
Remove unnecessary and dangerous re-initialisation of smc_v*_hashinfo.ht in
smc_init(); it is implicitly initialised to zero anyhow. Add
HLIST_HEAD_INIT to the definitions for clarity. |
| In the Linux kernel, the following vulnerability has been resolved:
net/iucv: fix locking in .getsockopt
Mirror iucv_sock_setsockopt() and wrap the whole switch in
lock_sock()/release_sock(). The pre-existing SO_MSGLIMIT-only lock
becomes redundant and is removed.
Any AF_IUCV HIPER user can potentially crash the kernel by racing
recvmsg() with getsockopt(SO_MSGSIZE): the SO_MSGSIZE arm dereferences
iucv->hs_dev->mtu after iucv_sock_close() (called from the racing
recvmsg()) has set hs_dev to NULL, producing a NULL pointer dereference
oops. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: core: Run queues for all non-SDEV_DEL devices from scsi_run_host_queues
While a SCSI host is in a recovery state, scsi_mq_requeue_cmd() will not
set the requeue list for a requeued command to be kicked in the future.
The expectation is a call to scsi_run_host_queues() will kick all SCSI
devices once the recovery state is cleared.
However, scsi_run_host_queues() uses shost_for_each_device() which uses
scsi_device_get() and so will ignore devices in a partially removed
state like SDEV_CANCEL. But these devices may also have requeued
requests, leaving their requests stuck from not being kicked and causing
the removal process of the device to hang.
scsi_run_host_queues() needs to run against more devices than the macro
shost_for_each_device() allows. Instead of using the too limiting
scsi_device_get() state checks, only ignore devices in SDEV_DEL state or
when unable to acquire a reference. Attempt to run the queues for all
other devices when scsi_run_host_queues() is called. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Fix race in do_task() when draining
When do_task() exhausts its iteration budget (!ret), it sets the state
to TASK_STATE_IDLE to reschedule, without a secondary check on the
current task->state. This can overwrite the TASK_STATE_DRAINING state
set by a concurrent call to rxe_cleanup_task() or rxe_disable_task().
While state changes are protected by a spinlock, both rxe_cleanup_task()
and rxe_disable_task() release the lock while waiting for the task to
finish draining in the while(!is_done(task)) loop. The race occurs if
do_task() hits its iteration limit and acquires the lock in this window.
The cleanup logic may then proceed while the task incorrectly
reschedules itself, leading to a potential use-after-free.
This bug was introduced during the migration from tasklets to workqueues,
where the special handling for the draining case was lost.
Fix this by restoring the original pre-migration behavior. If the state is
TASK_STATE_DRAINING when iterations are exhausted, set cont to 1 to
force a new loop iteration. This allows the task to finish its work, so
that a subsequent iteration can reach the switch statement and correctly
transition the state to TASK_STATE_DRAINED, stopping the task as intended. |
| In the Linux kernel, the following vulnerability has been resolved:
xsk: Harden userspace-supplied xdp_desc validation
Turned out certain clearly invalid values passed in xdp_desc from
userspace can pass xp_{,un}aligned_validate_desc() and then lead
to UBs or just invalid frames to be queued for xmit.
desc->len close to ``U32_MAX`` with a non-zero pool->tx_metadata_len
can cause positive integer overflow and wraparound, the same way low
enough desc->addr with a non-zero pool->tx_metadata_len can cause
negative integer overflow. Both scenarios can then pass the
validation successfully.
This doesn't happen with valid XSk applications, but can be used
to perform attacks.
Always promote desc->len to ``u64`` first to exclude positive
overflows of it. Use explicit check_{add,sub}_overflow() when
validating desc->addr (which is ``u64`` already).
bloat-o-meter reports a little growth of the code size:
add/remove: 0/0 grow/shrink: 2/1 up/down: 60/-16 (44)
Function old new delta
xskq_cons_peek_desc 299 330 +31
xsk_tx_peek_release_desc_batch 973 1002 +29
xsk_generic_xmit 3148 3132 -16
but hopefully this doesn't hurt the performance much. |
| In the Linux kernel, the following vulnerability has been resolved:
gfs2: Validate i_depth for exhash directories
A fuzzer test introduced corruption that ends up with a depth of 0 in
dir_e_read(), causing an undefined shift by 32 at:
index = hash >> (32 - dip->i_depth);
As calculated in an open-coded way in dir_make_exhash(), the minimum
depth for an exhash directory is ilog2(sdp->sd_hash_ptrs) and 0 is
invalid as sdp->sd_hash_ptrs is fixed as sdp->bsize / 16 at mount time.
So we can avoid the undefined behaviour by checking for depth values
lower than the minimum in gfs2_dinode_in(). Values greater than the
maximum are already being checked for there.
Also switch the calculation in dir_make_exhash() to use ilog2() to
clarify how the depth is calculated.
Tested with the syzkaller repro.c and xfstests '-g quick'. |
| In the Linux kernel, the following vulnerability has been resolved:
gve: prevent ethtool ops after shutdown
A crash can occur if an ethtool operation is invoked
after shutdown() is called.
shutdown() is invoked during system shutdown to stop DMA operations
without performing expensive deallocations. It is discouraged to
unregister the netdev in this path, so the device may still be visible
to userspace and kernel helpers.
In gve, shutdown() tears down most internal data structures. If an
ethtool operation is dispatched after shutdown(), it will dereference
freed or NULL pointers, leading to a kernel panic. While graceful
shutdown normally quiesces userspace before invoking the reboot
syscall, forced shutdowns (as observed on GCP VMs) can still trigger
this path.
Fix by calling netif_device_detach() in shutdown().
This marks the device as detached so the ethtool ioctl handler
will skip dispatching operations to the driver. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Limit access to parser->buffer when trace_get_user failed
When the length of the string written to set_ftrace_filter exceeds
FTRACE_BUFF_MAX, the following KASAN alarm will be triggered:
BUG: KASAN: slab-out-of-bounds in strsep+0x18c/0x1b0
Read of size 1 at addr ffff0000d00bd5ba by task ash/165
CPU: 1 UID: 0 PID: 165 Comm: ash Not tainted 6.16.0-g6bcdbd62bd56-dirty
Hardware name: linux,dummy-virt (DT)
Call trace:
show_stack+0x34/0x50 (C)
dump_stack_lvl+0xa0/0x158
print_address_description.constprop.0+0x88/0x398
print_report+0xb0/0x280
kasan_report+0xa4/0xf0
__asan_report_load1_noabort+0x20/0x30
strsep+0x18c/0x1b0
ftrace_process_regex.isra.0+0x100/0x2d8
ftrace_regex_release+0x484/0x618
__fput+0x364/0xa58
____fput+0x28/0x40
task_work_run+0x154/0x278
do_notify_resume+0x1f0/0x220
el0_svc+0xec/0xf0
el0t_64_sync_handler+0xa0/0xe8
el0t_64_sync+0x1ac/0x1b0
The reason is that trace_get_user will fail when processing a string
longer than FTRACE_BUFF_MAX, but not set the end of parser->buffer to 0.
Then an OOB access will be triggered in ftrace_regex_release->
ftrace_process_regex->strsep->strpbrk. We can solve this problem by
limiting access to parser->buffer when trace_get_user failed. |
| In the Linux kernel, the following vulnerability has been resolved:
ftrace: Also allocate and copy hash for reading of filter files
Currently the reader of set_ftrace_filter and set_ftrace_notrace just adds
the pointer to the global tracer hash to its iterator. Unlike the writer
that allocates a copy of the hash, the reader keeps the pointer to the
filter hashes. This is problematic because this pointer is static across
function calls that release the locks that can update the global tracer
hashes. This can cause UAF and similar bugs.
Allocate and copy the hash for reading the filter files like it is done
for the writers. This not only fixes UAF bugs, but also makes the code a
bit simpler as it doesn't have to differentiate when to free the
iterator's hash between writers and readers. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Don't (re)check L1 intercepts when completing userspace I/O
When completing emulation of instruction that generated a userspace exit
for I/O, don't recheck L1 intercepts as KVM has already finished that
phase of instruction execution, i.e. has already committed to allowing L2
to perform I/O. If L1 (or host userspace) modifies the I/O permission
bitmaps during the exit to userspace, KVM will treat the access as being
intercepted despite already having emulated the I/O access.
Pivot on EMULTYPE_NO_DECODE to detect that KVM is completing emulation.
Of the three users of EMULTYPE_NO_DECODE, only complete_emulated_io() (the
intended "recipient") can reach the code in question. gp_interception()'s
use is mutually exclusive with is_guest_mode(), and
complete_emulated_insn_gp() unconditionally pairs EMULTYPE_NO_DECODE with
EMULTYPE_SKIP.
The bad behavior was detected by a syzkaller program that toggles port I/O
interception during the userspace I/O exit, ultimately resulting in a WARN
on vcpu->arch.pio.count being non-zero due to KVM no completing emulation
of the I/O instruction.
WARNING: CPU: 23 PID: 1083 at arch/x86/kvm/x86.c:8039 emulator_pio_in_out+0x154/0x170 [kvm]
Modules linked in: kvm_intel kvm irqbypass
CPU: 23 UID: 1000 PID: 1083 Comm: repro Not tainted 6.16.0-rc5-c1610d2d66b1-next-vm #74 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:emulator_pio_in_out+0x154/0x170 [kvm]
PKRU: 55555554
Call Trace:
<TASK>
kvm_fast_pio+0xd6/0x1d0 [kvm]
vmx_handle_exit+0x149/0x610 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0xda8/0x1ac0 [kvm]
kvm_vcpu_ioctl+0x244/0x8c0 [kvm]
__x64_sys_ioctl+0x8a/0xd0
do_syscall_64+0x5d/0xc60
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: Correct tid cleanup when tid setup fails
Currently, if any error occurs during ath12k_dp_rx_peer_tid_setup(),
the tid value is already incremented, even though the corresponding
TID is not actually allocated. Proceed to
ath12k_dp_rx_peer_tid_delete() starting from unallocated tid,
which might leads to freeing unallocated TID and cause potential
crash or out-of-bounds access.
Hence, fix by correctly decrementing tid before cleanup to match only
the successfully allocated TIDs.
Also, remove tid-- from failure case of ath12k_dp_rx_peer_frag_setup(),
as decrementing the tid before cleanup in loop will take care of this.
Compile tested only. |